Application
Appliedin the Justice Sector(Prisons, detention centers, labor camp, police, courts,procuratorate);the Education Industry(School examination room, classrooms,dormitories, various social test sites, education and training institutions);Government agencies, administrative institutions meeting rooms; Factories andenterprises warehouses, workshops, production lines; Forces and confidentialunits, theaters, concert halls, memorial halls ,etc.
TechnicalParameter
■ Wayof communication and networking: remote-controlled by TCP/IP protocols withstandard RJ45 network interface
■ Jammingrange: Radius: 10~60m (-75dBm, depending on the distance of base station)
■ Transmissionpower: The whole set: 30W at maximum, each channel 2~3W
■ Jammedsignal type: (Notes:List common formats only)
5GNR:n41/n77/n78/n79
TDD-LTE:B34/B38/B39/B40/B41；
TD-SCDMA:B34/B39；
FDD-LTE:B1/B2/B3/B4/B5/B6/B7/B8/B9/B12/B17/B18/B19/B20/B26;
CDMA:BC0;
UMTS(WCDMA)/HSPA+/DC-HSDPA:B1/B2/B4/B5/B6/B8/B19;
GSM:B2/B3/B5/B8;
■ DataService:5GNR/TD-LTE/FDD-LTE/WCDMA/HSPA+/DC-HSDPA
/EVD0/CDMA1X/EDGE/GPRS/VoLTE/
ViLTE/WiFi2.4G/WiFi5.8G
Features
■ Intelligent networking through TCP/IP when connecting withnetwork cable with independent IP address;
■ Remote-controlled by main control software, to realize point/grouping/fullcontrolled on/off ;
■ Fault alarm and query, timing switch with schedule setting freedom;
■ Remote on/off or adjusting transmission power of any channel of any jammers;
■ Eight modules work independently, RF power of each channel is 2~3W;
■ Effectively jamming Mobile, Unicom and Telecom all 2G/3G/4G/5G signals;
■ Industrial switch power supply, with precision voltage regulator circuit, toensure the normal work of the host;
■ Fully sealed protective casing design, waterproof, dustproof, prevent fromsabotage and other questions in special application field;
■ Cooling base with ventilation pipe design, adjusted speed of cooling fans ;
■ Stable performance, long service life, harmless to human body;
Main Parts
DetailedTechnical Parameter
Band Parameter | Channel | Frequency | Average output power |
CDMA | 865-885MHz | ≤4W | |
GSM | 925-960MHz | ≤4W | |
DCS/ FDD | 1805-1880MHz | ≤2.5W | |
TDD-LTE | 1880-1920MHz | ≤2.5W | |
TD-SCDMA | 2010-2025MHz | ≤2.5W | |
WCDMA | 2110-2170MHz | ≤2.5W | |
WIFI2.4G | 2300-2500MHz | ≤2.5W | |
5G NR N41 | 2515-2675MHz | ≤2.5W | |
5G NR N78 | 3400-3500MHz | ≤2.5W | |
5G NR N78 | 3500-3600MHz | ≤2.5W | |
5G NR N79 | 4800-4900MHz | ≤2.5W | |
WIFI5.8G | 5725-5850MHz | ≤2.5W | |
Size | 410x342x106 | ||
Total weight | 4.8Kg | ||
Ambient temperature | -40-55℃ | ||
Relative humidity | 35-85% | ||
Power consumption | 160W | ||
Power input | AC 100V-240V | ||
Power output | DC：5V/40A | ||
Installation height | 1.8m-2.5m | ||
Installation mode | indoor/outdoor | ||
Enclosure material | plastic molding injection | ||
Partname
Considerations
■Jamming range is closely related to the signal strength in the field and may beaffected by the system of mobile phone;
■ Factors that affect jamming range include but not limited to: distance ofbase station, orientation, obstacles, wall’s material quality, jammer’sinstallation height and mode, etc;
■Strictly factory test, like aging test. When client receives the machine,please check whether there are something wrong with our device in transit, suchas parts fall off , and contact with dealer or manufacturer, for repairingtimely;
■ Installation height is recommended to be 1.8 to 2.5 meters. Install in areaswith no obstructions between the target positions. Antenna must be vertical, orantenna is vertical upright on the desktop after breaking off 90 degree, makesure no AC power lines or other audio and video line around antenna in range of0.2 meters;
■ In order to avoid possible interference with some electronic devices duringuse, keep the following common device away from 1 to 2 meters: audio, wirelessmicrophones, radios, computers, TV, Wi-Fi routers, etc.;
TheMothrboard Design
■The RF channel modular and each channel work individually
■ All the motherboard components are used SMT technology
■ All components are new and original
Advantages
1、Exclusive power amplifierheat sink, large heat dissipation base design
■326x93x40mm large heat dissipation base，Fast absorption and emission of heatfrom power amplifier and power board
■The natural wind (cold wind) goes up along the fin gap, bringing out the heaton the cooling teeth quickly and going up
■ Atotal of 4 ultra quiet cooling fans (almost no wind noise, adjustable speed) onboth sides of the upper end discharge the hot
2、Cold and hot air lower in andup out, waterproof and damage proof shell
3、The upgrade space is sufficient and can beexpanded to 24 channels at most
■Meet the upgrading needs of 6G or even 7G in the future;
■Reserve the expansion space of dual radiator, dual 12 channel module (24channels in total) and dual power supply;
■Function upgrading, expansion, original parts are all reserved and neverwasted.
OEMCustomized Service
■Frequency spreading can be done for Wi-Fi, Bluetooth, Intercom and wirelessdata transmit etc.
■ More than 50 units can provide screen printing OEM service.
■ Provide neutral device.
Jamming&MonitoringSystem Software
■Intelligentnetworking through TCP/IP protocols, with built-in independent IP address;
■Unified centralized control multiple units across city throughremote networking;
■B/S framework server platform, providing browser login management;
■Timing on/off jammers, the schedule can be set freedom;
■Controlled by point to point or grouping control;
■Real time monitoring work status of jammers;
■Optionally remote on/off each channel of jammers;
■Remote adjust transmission power of each channel of jammers;
■Fault query and alarm of jammers;
■Real timemonitoring of jammer working state
TCP/IP Network Mobile Signal Jamming System Connection Topology
TCP/IP NetworkJamming System Installation Application Diagram
TCP/IP Jamming System Networking Across City Topology
EngineeringApplication
Inengineering application, the four corners behind the main engine are reservedwith bolt holes for wall mounting, which can be directly mounted on thewall:：
■The installation bolt holes on the back of the equipment can be installed withconcealed hanging pieces (thickness 4mm), so as to keep the gap between theequipment and the wall and ventilate;
■Silent fans on both sides of device, strengthened to cool the host and powersupply
■Built-in antenna protect it from personnel sabotage
■Internal power supply protect it from sabotage and malicious power off
■Waterproof design, available installation both inside and outside
Field Application
